Home Decor

How to Install a Deadbolt Lock in Just a Few Simple Steps?

Adding a deadbolt lock to your entryway is not only a simple home improvement project. It’s also one that can add to your safety and security. We’ll teach you how to prepare your door and how to install a deadbolt lock in just a few simple steps.

Deadbolts will work on almost any exterior door. Come in a variety of models, some offer keyed entry or come as a combo set that includes a knob or lever that uses the same key as the deadbolt. Newer products feature keypads that allow you to program a personal entry code which is what we’re installing on this door.

Tools Needed

The steps we say you apply the most deadbolt installations our instructions will also work on wood fiberglass and most steel doors. For this project, the tools and materials you’ll need include a deadbolt lock, screwdrivers and you might need batteries if you have an electronic lock. If your door is not pre-board you’ll need a tape measure, ruler a square, a pencil, masking tape, drill with driver and drill bits 2 and 1/8 inch and 1-inch hole saws, a hammer and chisel, a dust mask and safety glasses.

A lockset template can make boring the holes for your lock easier.

Instructions Template

Your deadbolt instructions will come with a paper template. Before getting started is sure to review the manufacturer’s instructions some locks may install differently. After reviewing the instruction template you will know more about how to install a deadbolt lock for your safety and security. If you have an existing deadbolt the job will be easier to remove it takes out the screws. Then pull out the lock and thumb turn assembly. Then remove the actual deadbolt leaving an empty hole for the new lock.

Installations instructions

Just be sure the hole you have in your door matches the manufacturer’s specs. You’ll also want to measure your door’s thickness it should be between 1 and 3/8 and 1 and 3/4 of an inch.

Now, what can we do if your door isn’t pre-board? If you’re just replacing an existing deadbolt you can skip this step.

To prepare your door please decide where you want the lock to be placed. Typically it’s about six to twelve inches above the door-handle. Draw a horizontal line at this point on the interior side of the door and the jamb. You might find it easier to remove the door from the hinges and work on sawhorses. To bore, the holes select the backset on the template. The backset is the distance from the edge of the door to the center of the hole. Typically it’s either two and 3/8 inches or two and 3/4 inches and you’ll most likely want to match the placement of your door handle.

Align the template with the line you drew earlier. Drill to 1/8 inch pilot holes for the screws and secure the template to the door edge. You’ll use these holes again when you secure the latch. Now use a 2 and 1/8 inch hole saw. To drill the hole for the lock body to prevent the door from splintering drill halfway through one side. Then drill the rest from the other side. Use a 1-inch drill bit or hole saw. To drill the hole on the door edge for the deadbolt then remove the template from the door.

Now, this is the actual bolt itself. If you’re replacing the lock it’ll save time to match the old faceplate it will either have rounded or squared corners. Most deadbolts come with both you can switch it by prying off the one you don’t want and swapping it for the other. If you drilled a new hole slide the deadbolt into the hole and trace around the edge. Our kid has a jig for the faceplate just attach the jig to the door and with a drill use the router bit to cut along the grooves. Then chisel out the center part left by the router. Your door is now prepped.

Let’s talk about the jamb. At the mark, you made earlier drill two intersecting holes following the installation instructions. Drill deep enough so the deadbolt can fully extend without interference. Chisel out any excess material, place the strike against the hole, trace around it and mark the screw holes.

Drill 1/8 inch pilot holes for the screws. Then use a chisel to create a mortise for the strike. Now whether using the holes you just prepared or the ones left by the previous lock. Now it’s time to install the hardware. To fit the deadbolt make sure the top is pointing up. Slide it into the hole and attach the faceplate with screws. Retract the deadbolt if it’s not already.

Keypad install

If you have a keypad install it now again make sure the top is pointing up and the deadbolt is retracted. From inside the door install the mounting plate. Make sure the top is pointing up. Install the screws. Connect the cable then the battery. Tuck in the battery and the cables and attach the thumb turn.

Now move onto the jam your lock may come with a dust box that provides additional security from kicking attacks on your door. Insert the dust box into the hole and secure it using the supplied screws.

Finally, position the strike and attach it using the supplied strike screws. Close the door and use the thumb turn to check that the deadbolt fully extends. Then follow the manufacturer’s instructions to program the keypad.

And your deadbolt is ready to use a simple home improvement project that adds peace of mind. Now you also ready how to install a deadbolt lock. To know other home improvement projects you can check out blogs.

 

Tags
Show More

Dulsu Virgo

Hello World! This is DulsuVirgo. I am a blog writer. I like to write anything. Most of the time I passed to write something.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
Close